combined dust collector includes frame, motor, fan, electric control box, dust filter bag, door, vibration motor, vibration mechanism, hopper, dust catcher, dust catcher door and dust filter frame, the frame includes upper shell and lower shell, motor and fan are arranged in the upper shell, dust filter bag, drop hopper and dust catcher are arranged in the lower shell. The filter is arranged between the upper shell and the lower shell, the filter bag is connected with the filter frame, the elastic seal is arranged between the frame and the filter frame, the vibration motor is connected with the filter frame through the vibration mechanism, the air inlet is arranged on one side of the lower shell, the air outlet is arranged above the upper shell, and the motor and the vibration motor are respectively connected with the electric control box. The dust collector has the characteristics of compact structure, easy operation, low noise, good dust removal effect, and can be directly applied to small places and laboratories.

Here is an overview of the combined dust collector's daily operations:

1. Recovery filtration: After backblowing, the solenoid valve is closed, the cleaning operation of the system is completed, and the filter bag is restored to the filtration state;

Second, dust bag ash interception: dust containing gas into the filter bag, a large amount of dust is intercepted on the filter bag, and the air flow through the filter bag to achieve purification;

Third, ash hopper ash removal: ash removal device and dust collector run at the same time, should be cleaned in time, ash hopper as far as possible not to accumulate ash, otherwise it will affect the service life of the filter bag;

4. Discharge clean flue gas: the purified air flow enters the water film dust removal desulfurizer through the bag room;

combined dust collector induced draft fan inhalation: In normal operation, under the action of the induced draft fan, the dust-containing gas is sucked into the intake manifold and evenly distributed to each intake chamber through each intake branch pipe;

6. Air blowback: With the thickening of dust attached to the surface of the filter bag fabric, the resistance of the combined dust collector continues to rise, and it is necessary to clean the dust regularly. The whole cleaning process is mainly completed by the action of high-pressure gas storage bag, solenoid valve, blowpipe and cleaning control mechanism. First, the control system automatically opens the solenoid valve in order, and the high-pressure air is blown back through the spray pipe, so that the dust adhering to the dust bag is washed and shaken off into the ash hopper;

7. combined dust collector cycle dust filter: the control system opens other solenoid valves to clean the other filter bags, and all filter bags pass through the dust cycle to achieve the purpose of dust cleaning, and the dust collector restores the filtering state.

combined dust collector The main reason for the bad shaking mechanism is the joint bearing. In practice, if the hole of the joint bearing is worn long, the rocker rod hardly moves when the rocking motor is running. The reason is that when designing this mechanism, the rocking time is stipulated to be 30s, so this time is sufficient. There are two joint bearings in the rocking mechanism, the above one is connected with the motor eccentric, the following one is connected with the rocker crank, and the bearing connected with the eccentric wheel runs in a circular motion, while the other only does reciprocating motion. Accordingly, the above bearing connected with the eccentric wheel has a large operating amplitude, and it is also easy to heat. When the continuous operation time is less than 30s, there is no problem with slight heating. If the operation time is extended to more than 1min, it will heat up, which will seriously burn the bearing. Therefore, the shaking cleaning time cannot be arbitrarily changed when selecting the combined dust collector.

combined dust collector The main reason for the bad shaking mechanism is the joint bearing. In practice, if the hole of the joint bearing is worn long, the rocker rod hardly moves when the rocking motor is running. The reason is that when designing this mechanism, the rocking time is stipulated to be 30s, so this time is sufficient. There are two joint bearings in the rocking mechanism, the above one is connected with the motor eccentric, the following one is connected with the rocker crank, and the bearing connected with the eccentric wheel runs in a circular motion, while the other only does reciprocating motion. Accordingly, the above bearing connected with the eccentric wheel has a large operating amplitude, and it is also easy to heat. When the continuous operation time is less than 30s, there is no problem with slight heating. If the operation time is extended to more than 1min, it will heat up, which will seriously burn the bearing. Therefore, the shaking cleaning time cannot be arbitrarily changed when selecting the combined dust collector.

combined dust collector https://www.kaisenfilter.com/KSZHDM-01-Combined-Grinding-Dust-Collector.html